Beach Flags For Sale

Beach Flags For Sale

Beach Flags For Sale

custom flags   trade show table covers   Custom Tents   Beach Flags

Beach Flags For Sale   Beach Flags For Sale


Absorbent 40 ~ 100g/m2 Beach Flags For Sale


Permeability 500 ~~ of 2000ml/min


Weight of 60 ~ 70g/m2


pH of 4.5 to 5.5


Dust is not allowed Sizes Of Flags


Flower paper base abroad, the entire department softwood pulp manufacturing, which accounted for 50% of chemical pulp, mechanical pulp (50%). This paper Desiccant. Ink desiccant adding about 5 to 8 percent of the total ink, plus easy to dry, plus much affect the adhesion of the ink. Beach Flags For Sale


(4) the quality of screen  signage requirements. The text of the silk screen signs, scale, graphics, positioning holes and color should be consistent with the requirements of the drawings, the finished surface should be no obvious scratches, stains, ink film adhesion shall meet the requirements.



 Cheap Promotional Flags Banners



Phosphate primer in the metal screen




Metal silk screen  material is black or non-ferrous metals such as steel, iron, copper. Such as aluminum, zinc, and their common feature is the surface easy to rust or oxidation, Beach Flags For Sale and the surface is relatively smooth, which can easily lead to poor adhesion of screen  inks and metals, as well as peel off. To solve this problem, a series of pre-treatment (rust, cleaning, phosphating, passivation, etc.) must be not only a lot of manpower and materials, and to extend the duration. This book presents an easy way, before printed silk, coated with a layer of etch primer on the metal surface, not only can greatly simplify the process of pre-treatment, and to enhance ink adhesion. The etch primer, also known as a wash primer, polyvinyl small hard resin and phosphoric acid, zinc chrome yellow, alcohols such as modulation by an advanced anti-rust paint. It is divided into one component and two-component two (also known as single liquid-liquid type), single component etch primer preparation; two-component etch primer market the sale of goods.


A. Single component etch primer. Beach Flags For Sale


formula: Custom Flag Maker


Material Name Percentage (%) Weight (g)


Polyvinyl acetal plastic 10.95 176.05


33.3% chromic acid solution 1.40 22.51


10% phosphoric acid solution in acetone 10.95 176.05


Ethanol 62.20 1000.00


Butanol 14.50 233.12


Preparation method: with an appropriate amount of alumina, add twice as much distilled water Stir lead-acid aqueous solution is 33.3%, spare. Promotional Flag Makers


With an appropriate amount of phosphoric acid, dissolved in nine times the acetone solution is 10% phosphoric acid solution in acetone, spare.


The formula proportion of ethanol, butanol mixed, add the polyvinyl acetal plastic Stir to make it fully dissolved, and then added to the chromic acid aqueous solution and phosphoric acid in acetone solution, Stir can be used.


Two. Two-component etch primer.


phosphating paint liquid formula:


Material Name Weight (g) Beach Flags For Sale


Polyvinyl butyral 9


Basic chromate of zinc (zinc chrome yellow) 8.625


Talc 1.375


Ethanol 60.875


Positive butanol 20.125


acidic phosphating solution:


Orthophosphoric acid (85% phosphoric acid) 4.5


Water (distilled water) 2.188


Ethanol 18.312


Thinner: Promotional Flags China


90% of the ethanol industry (more than 96% alcohol)


Butanol 30%


The two components of the two-component etch primer is stored separately custody. Phosphate liquid paint can be put into metal containers (iron), the phosphating solution is required into the non-metallic container (plastic bucket). Use liquid paint, phosphating solution ratio of 4:1 is now against the 80% liquid paint phosphating solution of 20% (by weight), stir and place half an hour, allowed to fully reflect and then use . According to how much of the construction volume against time run out, or leftover paint expire after 12 hours, resulting in waste. Use, such as with a good etch primer is too thick, Beach Flags For Sale can not change the ratio of the two, you can add some thinner, thinner can also be used as cleaning tools and containers.


Feather Flags Feather Flags Wholesale Custom Feather Flags

Feather Flag & Pole & Spike & Base: As low as $49.00 to $59.00 !
Custom 3x5 Flags: As low as $6.00 to $13.50 !
Hand Flags: As low as $0.50 to $1.50 !
Car Flags: As low as $1.00 to $3.00 !
  All pricing based on quantity desired.
Unlimited Colors & No Set-up Fee's!

Minimum Order: 1

 custom printed flags
  • Color:  Any colors are available, Unlimited Colors & No Set-up Fee's!

  • Logo:  Any logos are available

  • Flags Material:   Knitted material / 100% Polyester / Nylon / Cotton / Satin and etc

  • Flagpole Material:  Aluminium alloy / Fiberglass / Wooden / Plastic

  • Normal Flag Size:   2'x3', 3'x5', 4'x6', 5'x8' and can be customized.
  • Hand Flag Size:  5"x8",  8"x12", 12"x18" and can be customized.
  • Car Flag Size:  8"x12", 12"x18" and can be customized.
  • Feather Flag/Teardrop Flag size:
  • S, pole total height is 8.5ft, after setting up, it is about 7ft.  (flag size: about  5.8'x1.3' ) 
    M, pole total height is 11 ft, after setting up, it is about 9.2ft. (flag size: about 7.9'x2.0' )
    L, pole total height is 15.1ft, after setting up, it is about 13ft.  (flag size: about 11.2'x2.3' )
    XL, pole total height is 18.4ft, after setting up, it is about 16ft. (flag size: about 13.5'x2.6' )

  • Delivery Time:    small order – 1 to 2 days, big order – 10 to 15 days

  • Shipping Time:  1 to 2 days to North America, Europe.
  •                                           2 to 3 days to Australia, New Zealand.
  •                                           3 to 5 days to other countries.