Beachflags



Beachflags

Beachflags


custom flags   trade show table covers   Custom Tents   Beach Flags

Beachflags   Beachflags

 

resulting in staining Beachflags The flaws of the product's color and the white star, seriously affecting the quality of the product of staining. The yarn quality index is a combination of the yarn thickness to express the strong data, weaving, dyeing and finishing process, the higher the quality indicators, Swooper Flag Poles the more beneficial. Used as weft yarn quality indicators than as a high. Yarn twist of uneven impact of dyeing and finishing products, Beachflags yarn count twist that would increase the fabric light Optional weakened, feel hardening lower dyeability, shrinkage increases, the grinding weakened, curly increase, but also smooth brushed flannel fabric. Fabric weft twist increases, the direction of yarn increases,  and dyeing processing elongation of the greater. Uneven twist will affect the fabric surface appearance; synthetic fabric twist is too low, easy to pilling, even after dyeing and finishing difficult to prevent.

Yarn evenness uneven make the fabric surface rendering uneven weft IOUs, serious impact on the fabric surface appearance, especially in bleaching and dyeing. Beachflags

Neps on the yarn due to the low maturity of cotton fibers or stiff cotton ginning and spinning projects to deal with bad tangle made, was yellow or white round or flat nodular. In addition, still due to the scutching net residual cottonseed crumbs, crushed leaves, when spinning the mixed yarn. Beachflags Yarn with a more impurities in the cotton spinning, will affect the fabric appearance and fabric feel rough, grinding decreased, while increasing the difficulty of  and dyeing processing.

Blend of cotton and chemical fiber should be noted that different types of fiber blended yarn strength "hanging chain phenomenon, but also should consider the ease of  and dyeing processing. Teardrop Flags And Banners

(2) cause the dyed yarn faults factors of the defect. Beachflags

(1) yarn in the oil, colored defects, such as bamboo, oil slick yarn, the oil through the oil latitude, color by color weft and soot yarn, bleached fabric is very prominent, must pay special attention. Chemical fiber itself high whiteness should avoid the use of the above flaws yarn, pure chemical fiber spinning and blended fabrics.

(2) dark fabric neps by the tight, loose through tight twist yarn requirements are particularly high, white star of the dark fabric and yarn faults. Light-colored fabrics are stained light, hiding less easy to show, all kinds of defects, with the exception of the dark fabric, tight end, by loose, tight twist yarn has the same requirements on Beachflags the flower weft, cotton balls and other yarn defect requirements are also higher, otherwise easy to excellent and cloth White Star staining flaws.

(C) the quality of weaving products Custom Teardrop Flags

Dyeing and finishing processes, followed by weaving and weaving the quality of the products will directly affect the dyeing process of the final product quality. Quality of weaving products, one fabric appearance, such as Weft terry-shaped formation of pigtail flush spider's web, these flaws in the fine and high density fabric (poplin, khaki, etc.) is more prominent, the second is color fabric dyeing quality. Common Defects of the impact points shown in the following: Beachflags

Side of the fabric of the defect: the jagged edges, flouncing side Weft, wearing the wrong side, and while wiping the defect, bad side, flash and so will be further serious development in the dyeing and finishing process. The color edge is the yarn from the cloth woven into the edge of 0.5cm color. Colored yarn woven into the fabric edge into two categories: Personalized Advertising Flags one category is a temporary coloring mark used to distinguish the factory all kinds of fabric, not wrong purposes used in the dye should be easy to fade in addition pre-treatment processes of dyeing and finishing dyes, such as strong acid dyes, Beachflags weak acid dyes, direct dyes slightly better fastness will cause staining flaws; another color yarn dyeing fastness higher, in order to distinguish between factory and outside plant variety of textile and do colored yarn edge, Backpack Banner Advertising requiring colored yarn on dye in the dyeing and finishing can not fade, and the general use of vat dyes, but to take into account in scouring the high-temperature alkali conditions, Beachflags whether caused by the white, sticky color or take color. Shift printed with the dye in the fabric weaving factory shift superstructure should also consider to take the color of the stick.

Feather Flags Feather Flags Wholesale Custom Feather Flags


Feather Flag & Pole & Spike & Base: As low as $49.00 to $59.00 !
Custom 3x5 Flags: As low as $6.00 to $13.50 !
Hand Flags: As low as $0.50 to $1.50 !
Car Flags: As low as $1.00 to $3.00 !
  All pricing based on quantity desired.
 
Unlimited Colors & No Set-up Fee's!

Minimum Order: 1

 custom printed flags
 
  • Color:  Any colors are available, Unlimited Colors & No Set-up Fee's!

  • Logo:  Any logos are available

  • Flags Material:   Knitted material / 100% Polyester / Nylon / Cotton / Satin and etc

  • Flagpole Material:  Aluminium alloy / Fiberglass / Wooden / Plastic

  • Normal Flag Size:   2'x3', 3'x5', 4'x6', 5'x8' and can be customized.
  • Hand Flag Size:  5"x8",  8"x12", 12"x18" and can be customized.
  • Car Flag Size:  8"x12", 12"x18" and can be customized.
  • Feather Flag/Teardrop Flag size:
  • S, pole total height is 8.5ft, after setting up, it is about 7ft.  (flag size: about  5.8'x1.3' ) 
    M, pole total height is 11 ft, after setting up, it is about 9.2ft. (flag size: about 7.9'x2.0' )
    L, pole total height is 15.1ft, after setting up, it is about 13ft.  (flag size: about 11.2'x2.3' )
    XL, pole total height is 18.4ft, after setting up, it is about 16ft. (flag size: about 13.5'x2.6' )


  • Delivery Time:    small order – 1 to 2 days, big order – 10 to 15 days

  • Shipping Time:  1 to 2 days to North America, Europe.
  •                                           2 to 3 days to Australia, New Zealand.
  •                                           3 to 5 days to other countries.

Tags: