Buy Swooper Flags

Buy Swooper Flags


custom flags   trade show table covers   Custom Tents   Beach Flags

Buy Swooper Flags   Buy Swooper Flags

 

c) Counterpoint: the parts mounted on the fixture, Buy Swooper Flagsand a printed surface on the transfer rubber stencil pattern alignment, the pattern of the screen all to surface, to fixture.

 

d) ranging: Floor radius plus the fixture axis radius equal to the fixture arm length, ie, a fixed transfer rubber.

 

e) Positioning: overlap must be fixed parts fixture wire transfer rubber lead or with a homemade jig to ensure.

 

f) try to print: a variety of factors, the transfer can not guarantee a successful, must try to print and correction, in order to make the 72 tick marks evenly distributed on the circumference of the cone, the starting line and terminate the line exactly.

 

g) Transfer: After the success of the pilot India to start mass production must, when the transfer pressure is moderate, so that the fullness of the parts on the writing. Buy Beach Flags

 

h) repair: where individual shortcomings with a brush dipped in ink to repair, reaching the eligibility requirements.

 

i) Drying: in an oven heated to 80 ~ 85 ° C, time 1. 5 to 2 hours.

 

j) cover varnish: spray a layer of varnish, Buy Swooper Flags to increase protection for light kerosene.

 

k) The natural drying: air dry at room temperature for 1 to 1.5 hours.

 

l) Packing: Inner packing with a special box with capacitor paper, packaging.

 

the requirements of special fixtures. Buy Swooper Flags

 

a. Parts mounted on the fixture, fixtures to ensure stable and solid parts and an appropriate degree, running freely.

 

and b. Fixture fixed axis must be perpendicular to the transfer rubber. Backpack Banner

 

(c) Should make the paste transfer rubber of plywood flat, precisely matched.

 

(d) Loading and unloading parts, in order to ensure the smooth conduct of the transfer concept.

 

The Notes. Buy Swooper Flags

 

a. Enlargement computer drawing, to ensure that the bottom plate deviation about the dry one.

 

and b. Transfer pressure is moderate, the pressure is too large or too small will cause deformation or incomplete pattern.

 

(c) System good screen must be the anti-version.

 

(d) Note the cleanliness of the environment.

 

e. Sticky transfer rubber of the tablet must be precise and special fixtures tie.  Custom Feather Flags

 

11. Melamine oxidation signage. Signs melamine anodizing surface was enamel-like, soft and shiny, with very good resistance to anti-performance, high hardness and wear resistance, good thermal insulation and electrical insulation, better ability to cover and the preferred adsorption capacity instrumentation, Buy Swooper Flags especially the decoration of the high-end machine to share. The production process of chromium-containing gas to escape, Custom Teardrop Flags to operate the equipment shall be provided with good ventilation and ventilation equipment in order to avoid poisoning.

 

Feather Flags Feather Flags Wholesale Custom Feather Flags


Feather Flag & Pole & Spike & Base: As low as $49.00 to $59.00 !
Custom 3x5 Flags: As low as $6.00 to $13.50 !
Hand Flags: As low as $0.50 to $1.50 !
Car Flags: As low as $1.00 to $3.00 !
  All pricing based on quantity desired.
 
Unlimited Colors & No Set-up Fee's!

Minimum Order: 1

 custom printed flags
 
  • Color:  Any colors are available, Unlimited Colors & No Set-up Fee's!

  • Logo:  Any logos are available

  • Flags Material:   Knitted material / 100% Polyester / Nylon / Cotton / Satin and etc

  • Flagpole Material:  Aluminium alloy / Fiberglass / Wooden / Plastic

  • Normal Flag Size:   2'x3', 3'x5', 4'x6', 5'x8' and can be customized.
  • Hand Flag Size:  5"x8",  8"x12", 12"x18" and can be customized.
  • Car Flag Size:  8"x12", 12"x18" and can be customized.
  • Feather Flag/Teardrop Flag size:
  • S, pole total height is 8.5ft, after setting up, it is about 7ft.  (flag size: about  5.8'x1.3' ) 
    M, pole total height is 11 ft, after setting up, it is about 9.2ft. (flag size: about 7.9'x2.0' )
    L, pole total height is 15.1ft, after setting up, it is about 13ft.  (flag size: about 11.2'x2.3' )
    XL, pole total height is 18.4ft, after setting up, it is about 16ft. (flag size: about 13.5'x2.6' )


  • Delivery Time:    small order – 1 to 2 days, big order – 10 to 15 days

  • Shipping Time:  1 to 2 days to North America, Europe.
  •                                           2 to 3 days to Australia, New Zealand.
  •                                           3 to 5 days to other countries.

Tags: