Custom Feather Flags Wholesale

Custom Feather Flags Wholesale


custom flags   trade show table covers   Custom Tents   Beach Flags

Custom Feather Flags Wholesale   Custom Feather Flags Wholesale

 

paste dosage and choice. Custom Feather Flags Wholesale The purpose of the burnt-out slurry paste is Physalis remain in relatively fixed pattern parts, to prevent the thin pulp and infiltration of cause flower damage, to ensure that the pattern contour line is clear and smooth. Slurry through the dilute up to less than a fixed rotten pulp in the flower bit of purpose; slurry too thick, poor penetration effect of flowers complete and the scraper run difficulties; Custom Feather Flags Wholesale operation effort, the cost of increasing the height, so the amount of the paste Select is also important conditions. Hand Waving Flags For Sale

 

Different paste, a great difference in the amount of burnt-out pulp. White dextrin with flowers a clear outline of pulp burnt-out products, burnt-out part of the white high bright color, but the viscosity is high, the operation is relatively inconvenient, shortage of supply. Long plastic with simple syrup, and immediately use, Custom Feather Flags Wholesale easy to produce in the burnt-out after the infiltration phenomenon, caused by the clear pattern outline as white dextrin with slurry. Can be two kinds of pulp mixed with used to fill the gap. Yellow dextrin with good pulp burnt-out effect, the contour line is clear and easy to operate with slurry, although with a pigment, the pigment traces are not found in the burnt-out parts in the proper understanding of the process conditions. Tapioca pulp can be used as a substitute paste for the burnt-out pulp, Cheap Garden Flags Wholesale generally used for the above slurry supply is insufficient.

 

Slurry dosage according to the specific mode of production to determine the machine printed and fingerprints with Jelly, under normal circumstances machine India paste can be a little thin in the fingerprints. Custom Feather Flags Wholesale

 

The amount of paste in the burnt-out plasma reference ranges are as follows; white dextrin, accounting for 12 to 20 percent the proportion of burnt-out pulp; Synthetic Long plastic accounts for the burnt-out plasma ratio of 2 to 4 percent.

 

carbonization conditions. Grasp of the carbonization process is the key to the quality of burnt-out, has a direct relationship with the ability to wash cotton fiber residue. Carbonization process plant equipment conditions can be different steaming or melting bake. Melting high baking temperature required to melt the baking time should be short, Custom Feather Flags Wholesale melt baking temperature is low, melt baking time should be long.

 

After paste  after the burnt-out fabric after heating, the burnt-out parts of a light yellow, with time, the color gradually deepened into a light brown, dark brown until black. In the cotton fibers showed black and brown, Personalised Football Flags and its residue is difficult to wash. The general temperature control is appropriate in light brown.

 

Select the temperature point, you should understand the thermal properties of chemical fibers, control below the softening point, bearing in mind the rotten and India combined with the temperature parameters of the  color fastness. Taken rotten, printed on both processes can not take into account the two-step production process is complicated, spent registering difficulty, to design flowers design for rotten in the two-step  type. Custom Feather Flags Wholesale

 

burnt-out silk screen of choice. The burnt-out polyester fiber is generally used, because of its long service life, but in the absence of polyester or nylon red wash version measures to be taken in the continuous production, to extend their useful life. Burnt-out silk screen mesh selection of burnt-out size, should not be used too close to prevent the resulting bad through the ills. But with too thin and prone to infiltration phenomenon.

 

The burnt-out plate making the selection of sensitive adhesive. Note that the selection of acid sensitive adhesive.

 

Feather Flags Feather Flags Wholesale Custom Feather Flags


Feather Flag & Pole & Spike & Base: As low as $49.00 to $59.00 !
Custom 3x5 Flags: As low as $6.00 to $13.50 !
Hand Flags: As low as $0.50 to $1.50 !
Car Flags: As low as $1.00 to $3.00 !
  All pricing based on quantity desired.
 
Unlimited Colors & No Set-up Fee's!

Minimum Order: 1

 custom printed flags
 
  • Color:  Any colors are available, Unlimited Colors & No Set-up Fee's!

  • Logo:  Any logos are available

  • Flags Material:   Knitted material / 100% Polyester / Nylon / Cotton / Satin and etc

  • Flagpole Material:  Aluminium alloy / Fiberglass / Wooden / Plastic

  • Normal Flag Size:   2'x3', 3'x5', 4'x6', 5'x8' and can be customized.
  • Hand Flag Size:  5"x8",  8"x12", 12"x18" and can be customized.
  • Car Flag Size:  8"x12", 12"x18" and can be customized.
  • Feather Flag/Teardrop Flag size:
  • S, pole total height is 8.5ft, after setting up, it is about 7ft.  (flag size: about  5.8'x1.3' ) 
    M, pole total height is 11 ft, after setting up, it is about 9.2ft. (flag size: about 7.9'x2.0' )
    L, pole total height is 15.1ft, after setting up, it is about 13ft.  (flag size: about 11.2'x2.3' )
    XL, pole total height is 18.4ft, after setting up, it is about 16ft. (flag size: about 13.5'x2.6' )


  • Delivery Time:    small order – 1 to 2 days, big order – 10 to 15 days

  • Shipping Time:  1 to 2 days to North America, Europe.
  •                                           2 to 3 days to Australia, New Zealand.
  •                                           3 to 5 days to other countries.

Tags: