Custom Wind Flags, Wind Flags

Custom Wind Flags, Wind Flags


custom flags   trade show table covers   Custom Tents   Beach Flags

Custom Wind Flags   Wind Flags

Wind Flags   Custom Wind Flags

 

folder network. Folder to network folder, Custom Wind Flags should be very careful to maintain the parallel side, so that the warp and weft threads and network folder, and, as far as possible, straight, should not have a cable-stayed network.

 

early pull. Only stretch up to 60% of the rated tension pull the net that early pull. Due to the characteristics of woven, requirements stretch slowly to force in order to facilitate the adjustment of the shape of the mesh and the acceleration of tension relaxation, but also prevents the tension to the risk of high tension nets, so take a step-by-step drawing in the net or incremental pull the net. Aspirated pull operation is as follows:

 

(a) adjusting air compressor pressure value should be greater than about 30% of the value of drawing in the net pressure;

 

(b) open air compressor valve and gas source controller valve; Custom Wind Flags

 

(c) to regulate the pressure gauge on the gas source controller to pull the pressure value; Custom Flag Maker Online

 

(d) to open the two pull-three links, hand valves, compressed air through the distributor to the cylinder, push the piston and the beginning of the pull action.

 

Early pull, you should double-check the network via parallels the situation found with network folders is not parallel to, should Matsushita, re-clip the heavy pull.

 

early pull after about 10 minutes, so that the beginning of pull tension, try relaxation.

 

heavy pull. Increasing pressure to rating, while the tonometer to measure the tension values ​​every 5 to 10 minutes of tension to compensate for the loss, Pneumatic Stretching automatic compensation; other Stretching artificial recharge shall be, that is, repeatedly tighten until tension stability in the ratings so far. General need to repeatedly tighten three times. Custom Wind Flags

 

fixed network. Nien net plastic active solvent to the adhesive surface spray or brush, then wipe with cotton yarn pressure bonding at the screen frame, as the whole sticky net surface presents a deep and uniform color, be considered fully bonded. If there is a light-colored area, the area coating should Coating; or frame surface and the network connection is bad, the available pressure iron pressure contact with the full after bonding. Once the adhesive part of the glue is completely dry, turn off the two three-way valve to cut off gas supply, pull the net inlet and air connectivity, the piston by a spring reset, you can release the network folder, remove the stencil.

 

(10) the whole side. Cut off excess wrapping, labeling, and coated with adhesive tape or add paint to protect the adhesive part from the erosion of harmful solvents, as shown in Figure 2-46. Personalized Flags

 

Removed from the stretching device to stretch after a good screen, durable and clean the screen, you need to do the following finishing: the excess cut and trim; side cut the rest of the network should be able to wrap outside the framework of side of the half, and cement at the edge of the box.

 

(11) Screen label. Order Custom Flags Online Stretched a good screen should be convenient in the framework of the Department (generally in the outer side of the screen frame), Custom Wind Flags specify the following contents: material, mesh, wire diameter and grade Stretching date. Such as:

 

Single yarn of nylon 110 HD 1985 04 03

 

Feather Flags Feather Flags Wholesale Custom Feather Flags


Feather Flag & Pole & Spike & Base: As low as $49.00 to $59.00 !
Custom 3x5 Flags: As low as $6.00 to $13.50 !
Hand Flags: As low as $0.50 to $1.50 !
Car Flags: As low as $1.00 to $3.00 !
  All pricing based on quantity desired.
 
Unlimited Colors & No Set-up Fee's!

Minimum Order: 1

 custom printed flags
 
  • Color:  Any colors are available, Unlimited Colors & No Set-up Fee's!

  • Logo:  Any logos are available

  • Flags Material:   Knitted material / 100% Polyester / Nylon / Cotton / Satin and etc

  • Flagpole Material:  Aluminium alloy / Fiberglass / Wooden / Plastic

  • Normal Flag Size:   2'x3', 3'x5', 4'x6', 5'x8' and can be customized.
  • Hand Flag Size:  5"x8",  8"x12", 12"x18" and can be customized.
  • Car Flag Size:  8"x12", 12"x18" and can be customized.
  • Feather Flag/Teardrop Flag size:
  • S, pole total height is 8.5ft, after setting up, it is about 7ft.  (flag size: about  5.8'x1.3' ) 
    M, pole total height is 11 ft, after setting up, it is about 9.2ft. (flag size: about 7.9'x2.0' )
    L, pole total height is 15.1ft, after setting up, it is about 13ft.  (flag size: about 11.2'x2.3' )
    XL, pole total height is 18.4ft, after setting up, it is about 16ft. (flag size: about 13.5'x2.6' )


  • Delivery Time:    small order – 1 to 2 days, big order – 10 to 15 days

  • Shipping Time:  1 to 2 days to North America, Europe.
  •                                           2 to 3 days to Australia, New Zealand.
  •                                           3 to 5 days to other countries.

Tags: