High Quality Flags For Sale, Quality Flags

High Quality Flags For Sale, Quality Flags


custom flags   trade show table covers   Custom Tents   Beach Flags

High Quality Flags For Sale   High Quality Flags For Sale

 Quality Flags   Quality FlagsSale

A. Braid is used as a plate support body.High Quality Flags For Sale Vulgar I tulle, silk screen, gauze, mesh and so on. (2) mesh. Mesh per square centimeter (cm2) with the number of mesh. The product specifications used to express the units of the mesh holes / cm or lines / cm. Countries and regions, of the use of imperial units of measurement to express the hole / inch or lines / inch mesh. The mesh can generally be described in the Confidential Memorandum of silk and silk. The higher the mesh is more dense, the smaller the mesh. On the contrary, the mesh, the lower the more sparse mesh the greater, such as 150 mesh / inch, 1 inches 150 mesh. Mesh the smaller the ink through the worse, the mesh the greater the ink, the better. According to the accuracy of the requirements in the selection, select the number of eyes. (3) thickness. The thickness refers to the the the distance between the the surface and the the the underside of are measured, the general in order to the millimeter (mm) or microns (μm). Thickness should be measured when standing in tension-free state. The thickness is determined by the diameter of the composition of over-the amount of ink and thickness, shown in Figure 2-1. Figure 2-1 Size schematic High Quality Flags For Sale 4. The opening degree of. The the opening degree of yes to used to describe the the Kong wide, aperture, the the important parameters of the web-Kong the size of. Opening degree of sophistication of product design, text. The opening actually represented by the width of the mesh, using the latitude and longitude of the network two-wire surrounded the square root of the mesh area to indicate the units (usually microns 1 micron = 1/1000 mm). Therefore, the length of the side of the mesh is the longer the opening of the larger. However, the same opening, due to the different woven into the materials and methods of operation, the effect both good and bad. Opening can be calculated as: O = A1 / 2 (ab) 1/2 -Style: the of O-to open degrees (μm); A-hole area; a, b-mesh adjacent to both sides of the width; Quality Flags L-metering unit length of the mesh, the use of metric units of measurement is 1cm, the use of imperial units of measurement is 1 inch, 1 inch = 2.54cm; M-mesh; T-wire diameter. 5 aperture ratio. Aperture ratio, also known as the rate of through-hole effective sieve area, the mesh area percentage per unit area, the percentage of mesh area. Shown in Figure 2-1, the aperture ratio can be calculated as: Aperture ratio = (a × b) / (C × D) × 100% = [SX (] × b [] (T) (b T) [SX)] × 100% Where: a × b-mesh area; Quality Flags C x D-area; T-wire diameter. Or opening rate = : O-opening (hole width); M-mesh; L-metering unit length of the mesh (cm or inches), the calculation should be converted to metric units. 6. Over the amount of ink. In the actual , by the amount of ink by the viscosity of the material, performance, specifications, ink, pigments and other ingredients, types of substrates, squeegee hardness, pressure, speed, and the version and the clearance of substrates and many other we condition and, therefore, no definite criteria. Are generally kept the as assumptions of the as shown in in Figure 2-2 a through volume called the Guo ink the amount of. Figure 2-2 ink volume simulation of Figure Performance terms. The ① density. Also known as density, fabric density. And weft unit length of wire (line) number of roots, number of roots along the zonal unit length by wire through the wire density along by the number of roots per unit length of the weft yarn for the weft density. When the warp density is equal to the zonal density, the density is equal to the number of specifications expressed in the head.

Feather Flag & Pole & Spike & Base: As low as $49.00 to $59.00 !
Custom 3x5 Flags: As low as $6.00 to $13.50 !
Hand Flags: As low as $0.50 to $1.50 !
Car Flags: As low as $1.00 to $3.00 !
  All pricing based on quantity desired.
 
Unlimited Colors & No Set-up Fee's!

Minimum Order: 1

 custom printed flags
 
  • Color:  Any colors are available, Unlimited Colors & No Set-up Fee's!

  • Logo:  Any logos are available

  • Flags Material:   Knitted material / 100% Polyester / Nylon / Cotton / Satin and etc

  • Flagpole Material:  Aluminium alloy / Fiberglass / Wooden / Plastic

  • Normal Flag Size:   2'x3', 3'x5', 4'x6', 5'x8' and can be customized.
  • Hand Flag Size:  5"x8",  8"x12", 12"x18" and can be customized.
  • Car Flag Size:  8"x12", 12"x18" and can be customized.
  • Feather Flag/Teardrop Flag size:
  • S, pole total height is 8.5ft, after setting up, it is about 7ft.  (flag size: about  5.8'x1.3' ) 
    M, pole total height is 11 ft, after setting up, it is about 9.2ft. (flag size: about 7.9'x2.0' )
    L, pole total height is 15.1ft, after setting up, it is about 13ft.  (flag size: about 11.2'x2.3' )
    XL, pole total height is 18.4ft, after setting up, it is about 16ft. (flag size: about 13.5'x2.6' )


  • Delivery Time:    small order – 1 to 2 days, big order – 10 to 15 days

  • Shipping Time:  1 to 2 days to North America, Europe.
  •                                           2 to 3 days to Australia, New Zealand.
  •                                           3 to 5 days to other countries.

Tags: