Football Flags

Personalised Football Flags, Football Flags

Personalised Football Flags, Football Flags

custom flags   trade show table covers   Custom Tents   Beach Flags

Personalised Football FlagsPersonalised Football Flags  


Example 2: formulation and production of gelatin film paper




Gelatin 20g


Water 100 ~ 300g


Glycerol 3 ~ 7g




a) gelatin into the container in full bloom in the water for cooking and melt, Personalised Football Flags then add the glycerin and a little royal blue dye mixing 100 mesh to Internet filtering. Small Flags Wholesale


b) polyester film base paste in a flat wooden anti-or glass, Personalised Football Flags with a brush, perchlorethylene and cyclohexanone solvent brushing a piece of paper for isolation layer, to be dry, spray or brush system spectrum can. (With the former method)


c) let it dry, place the dry and ventilate Department store spare.


On the version:


a) In the original painting to lay down the line, multi-chromatography to determine the rules in this rule line.


b) engraved with a good version, together with the original placed in the appropriate position of the stretched box, according to the rules of the original lines, the rules piece creamy white adhesive paste in the last, with a piece of paper affixed securely. Several sets of color with a few stretched the frame and sets out uniform rules.


c) of the manuscript together with carving the version placed in the bottom plate of a good set rules, Mini Flags Wholesale Personalised Football Flags put down the box, in the above with the iron at the carving the gelatin version of the four corners of the edge of designated gelatin version of sticky hot in the last thrown off the original sample .


d) In the bottom plate to put some thick cardboard, put down the box to make the next pad formation, a polyester film base from the interval covered gelatin film several times to iron in the iron back to the ironing.


e) Shanghao version, let it dry, then torn off the backing paper and cyclohexanone version sub-opposite and mount between brushing to perchlorethylene trace cleaned.


f) If the version off the local glacial acetic acid to make up the prison, if the blade phase of the marks and small strokes off can be a brush stick out glue repair. Personalised Football Flags


and b. Plate method of water-soluble film. Polyester film or paper with a special resin as the end of paper, coated with a layer of water-soluble resin layered film version of the film, known as water-soluble film. Hand Waving Flags For Sale Transparent resin version of the film is easy to cut from the end of paper easier, resin version of the film version of material that is resistant to all solvents, anti-Indian forces. But not suitable for fine text and pictorial plate.


Cut from the film Zheng film placed on the bottom plate of the appropriate size, with fixed with transparent tape. Version of the film along the bar and outer edge of text with a knife or a double-edged knife dug cut down. Shear after the film version of the film facing the platform. Rags give a uniform moisture, the moisture content should not be too much, however, also make too little bonding uneven. Contains water in the film, and then add some water, Personalised Football Flags with more dry cloth adhesive on gently push forward. Must pay attention to the glue evenly. Version of the film village lipid species, in addition to water, and sometimes need to add a small amount of acetic acid or alcohol. Film to follow the manufacturer's specified to do.




Figure 2-107 version of the membrane surface of the cut


Feather Flag & Pole & Spike & Base: As low as $49.00 to $59.00 !
Custom 3x5 Flags: As low as $6.00 to $13.50 !
Hand Flags: As low as $0.50 to $1.50 !
Car Flags: As low as $1.00 to $3.00 !
  All pricing based on quantity desired.
Unlimited Colors & No Set-up Fee's!

Minimum Order: 1

 custom printed flags
  • Color:  Any colors are available, Unlimited Colors & No Set-up Fee's!

  • Logo:  Any logos are available

  • Flags Material:   Knitted material / 100% Polyester / Nylon / Cotton / Satin and etc

  • Flagpole Material:  Aluminium alloy / Fiberglass / Wooden / Plastic

  • Normal Flag Size:   2'x3', 3'x5', 4'x6', 5'x8' and can be customized.
  • Hand Flag Size:  5"x8",  8"x12", 12"x18" and can be customized.
  • Car Flag Size:  8"x12", 12"x18" and can be customized.
  • Feather Flag/Teardrop Flag size:
  • S, pole total height is 8.5ft, after setting up, it is about 7ft.  (flag size: about  5.8'x1.3' ) 
    M, pole total height is 11 ft, after setting up, it is about 9.2ft. (flag size: about 7.9'x2.0' )
    L, pole total height is 15.1ft, after setting up, it is about 13ft.  (flag size: about 11.2'x2.3' )
    XL, pole total height is 18.4ft, after setting up, it is about 16ft. (flag size: about 13.5'x2.6' )

  • Delivery Time:    small order – 1 to 2 days, big order – 10 to 15 days

  • Shipping Time:  1 to 2 days to North America, Europe.
  •                                           2 to 3 days to Australia, New Zealand.
  •                                           3 to 5 days to other countries.