Printable Racing Flags



Printable Racing Flags

Printable Racing Flags


custom flags   trade show table covers   Custom Tents   Beach Flags

Printable Racing Flags   Printable Racing Flags

 

 (B) high temperature and high pressure dyeing process points Printable Racing Flags when dyeing polyester with disperse dye molecules is difficult to enter the fiber core, except a sealed high temperature high pressure dyeing machine through high temperature due to the close arrangement of the molecular structure of the polyester fiber porosity is extremely small, to promote fiber extruded in order to facilitate the staining, but also need to extend the dyeing time to overcome the resistance of the fiber for dye adsorption, in addition, must also try to increase the fineness of the dye particles. Beach Warning Flags For Sale At present, the high temperature and high pressure technology has been widely used in the dyeing of polyester and blended yarns, usually in confined conditions, with steam heating, pressurized to a temperature of 130 ° C staining. PH value when the stain is particularly important, Printable Racing Flags In addition, the dyeing temperature and time as well as water quality and so have a greater impact on the quality of dyeing of polyester. Usually high temperature and high pressure dyeing dye bath pH control in the weakly acidic range of 5 to 6, while adding an appropriate amount of dispersants in the dye bath. Selectable 120 ° C for the better diffusion properties of disperse dyes, coloring; poor diffusion properties of disperse dyes, dyeing need 125 to 130 ° C; individual dyeing worse dyes can increase the temperature to 140 staining ~ 1.5h. Decorative House Flags Free Shipping

Dye in a very thick layer of yarn in the high temperature and pressure yarn dyeing machine, reverse circulation, virtually the yarn into a filter layer, if the water is not good, not only caused by the light color, and will cause dye precipitation, filtration yarn on a dye spot. Should be used at high temperature and pressure yarn dyeing, soft water, in order to ensure the stability of the dyeing quality.

(C) high temperature and high pressure bobbin dyeing process example 100% polyester filament yarn, dyed light gray, winding density 0.33 ~ 0.35g/cm3 dye weight of 25kg (equivalent to 5 packet yarn with Printable Racing Flags 25 kg of high temperature and pressure dye vat)

Recipe:  Custom Decorative Garden Flags Wholesale

Scattered brown S-2RL 1.5g / package

Scattered red S-HBGL 1g / package

Disperse black D-2R 5.4g / package

Toho salt 200ml / cylinder

98% acetic acid 200ml / cylinder (adjust the dye dissolved pH)

105 Detergent 200mL / cylinder (soap boiling)

305 Hydroxyl silicone oil (emulsion) 3L / cylinder (anti-static, lubricants, defoamers)

Liquor ratio of 1:11.

Process: 40 warm water of open disperse dyes, stir to fully dispersed in added to a neutral soft water tank, and by adding acetic acid and Toho salt, and then open the pump, so that the dye cycle uniformity. The temperature to 80 °C, Custom Made Wind Flags packed yarn hanging into the cylinder, the dye positive cycle, and stamped with the heated to boiling, then drain the air pressure to keep the solution heated to 130 ° C in 4Omin insulation of dyeing 30min, and then cool the row pressure exhaust steam to below 90 , washed twice to open the cylinder head using soft water, soap boiling at 85 for 10min, Printable Racing Flags then soft water washing twice with silicone in the 35 ~ 40 the processing 2Omin ( not washed). Finally, the yarn hanging out cylinder, dry and dehydrated, complete the package yarn dyeing.

High temperature and high pressure dyeing, should avoid excessive temperature and excessive heating, flocculent and cohesion may be to prevent the disperse dyes. At elevated temperatures below 100 can be faster, more than 100 110 ~ 120 ° C, the dye uptake rate of the fastest, the need for strict control to prevent the dye too fast to produce flower color. Printable Racing Flags To make dye staining to fully penetrate into the fiber insulation staining should be controlled in 80 ~ 60min.


Feather Flag & Pole & Spike & Base: As low as $49.00 to $59.00 !
Custom 3x5 Flags: As low as $6.00 to $13.50 !
Hand Flags: As low as $0.50 to $1.50 !
Car Flags: As low as $1.00 to $3.00 !
  All pricing based on quantity desired.
 
Unlimited Colors & No Set-up Fee's!

Minimum Order: 1

 custom printed flags
 
  • Color:  Any colors are available, Unlimited Colors & No Set-up Fee's!

  • Logo:  Any logos are available

  • Flags Material:   Knitted material / 100% Polyester / Nylon / Cotton / Satin and etc

  • Flagpole Material:  Aluminium alloy / Fiberglass / Wooden / Plastic

  • Normal Flag Size:   2'x3', 3'x5', 4'x6', 5'x8' and can be customized.
  • Hand Flag Size:  5"x8",  8"x12", 12"x18" and can be customized.
  • Car Flag Size:  8"x12", 12"x18" and can be customized.
  • Feather Flag/Teardrop Flag size:
  • S, pole total height is 8.5ft, after setting up, it is about 7ft.  (flag size: about  5.8'x1.3' ) 
    M, pole total height is 11 ft, after setting up, it is about 9.2ft. (flag size: about 7.9'x2.0' )
    L, pole total height is 15.1ft, after setting up, it is about 13ft.  (flag size: about 11.2'x2.3' )
    XL, pole total height is 18.4ft, after setting up, it is about 16ft. (flag size: about 13.5'x2.6' )


  • Delivery Time:    small order – 1 to 2 days, big order – 10 to 15 days

  • Shipping Time:  1 to 2 days to North America, Europe.
  •                                           2 to 3 days to Australia, New Zealand.
  •                                           3 to 5 days to other countries.

Tags: